发信人: hover (羽), 信区: TJU 标 题: Foundry Switch and Router IP Tunnel Commands 发信站: 中国Cisco论坛 (2003年07月14日10:33:17 星期一), 站内信件 Foundry Switch and Router Command Line Interface Reference Chapter 14 IP Tunnel Commands ----------------------------------------------------------------------------- --- encap-control Enables or disables encapsulation of IP multicast control messages such as probe, route report, and so on using IP-IN-IP encapsulation on an IP Tunnel. EXAMPLE: BigIron(config-if-5/4)# ip tunnel 192.3.45.6 BigIron(config-if-pim-tunnel)# encap on Syntax: encap-control on | off Possible values: on, off Default value: off ----------------------------------------------------------------------------- --- end Moves activity to the privileged EXEC level from any level of the CLI except the user EXEC level. EXAMPLE: To move to the privileged level, enter the following from any level of the CLI. BigIron(config-if-4/5-tunnel)# end BigIron# Syntax: end Possible values: N/A Default value: N/A ----------------------------------------------------------------------------- --- exit Moves activity up one level from the current level. In this case, activity will be moved to the interface level. EXAMPLE: BigIron(config-if-4/5-tunnel)# exit BigIron(config-if-4/5)# Syntax: exit Possible values: N/A Default value: N/A ----------------------------------------------------------------------------- --- metric Sets the metric for an IP tunnel for use with the multicast protocol. ----------------------------------------------------------------------------- --- NOTE: Assign a higher metric to an IP tunnel than that of the interface, to ensure that the IP tunnel path takes precedence. ----------------------------------------------------------------------------- --- EXAMPLE: To define an IP tunnel metric (cost) of 15, enter the following: BigIron(config)# interface 5/2 BigIron(config-if-5/2)# ip tunnel 192.45.3.2 pim BigIron(config-if-pim-tunnel)# metric 15 Syntax: metric <1-255> Possible values: 1 - 255 Default value: N/A ----------------------------------------------------------------------------- --- no Disables other commands. To disable a command, place the word no before the command. ----------------------------------------------------------------------------- --- quit Returns you from any level of the CLI to the User EXEC mode. EXAMPLE: BigIron(config-if-4/5-tunnel)# quit BigIron> Syntax: quit Possible values: N/A Default value: N/A ----------------------------------------------------------------------------- --- show Displays a variety of configuration and statistical information about the device. See "Show Commands" . ----------------------------------------------------------------------------- --- ttl-threshold Specifies how long a packet is considered viable on an IP Tunnel link. EXAMPLE: BigIron(config-if-3/4)# ip tunnel BigIron(config-if-3/4-tunnel)# ttl 60 Syntax: ttl-threshold <value> Possible values: 1 - 254 Default value: 1 ----------------------------------------------------------------------------- --- write memory Saves the running configuration into the startup-config file. EXAMPLE: BigIron(config-if-3/4-tunnel)# wr mem Syntax: write memory Possible values: N/A Default value: N/A ----------------------------------------------------------------------------- --- write terminal Displays the running configuration of the Foundry device on the terminal screen. ----------------------------------------------------------------------------- --- NOTE: This command is equivalent to the show running-config command. ----------------------------------------------------------------------------- --- EXAMPLE: BigIron(config-if-3/4-tunnel)# wr term Syntax: write terminal Possible values: N/A Default value: N/A -- 香草来自马达加斯加,咖啡来自巴西,草莓来自俄勒冈 巧克力来自比利时,坚果来自夏威夷... 我的理想... 来自你 ※ 来源:·中国Cisco论坛 bbs.ccxx.net·[FROM: el océano profundo] |
|
Foundry Switch and Router DVMRP Commands usedful link of juniper juniper路由器上路由协议的权值(管辖距离) 请不要做浮躁的人 关于EIGRP一些小问题的解答(From NET130) Re: [恶搞]华为新员工转正笔试题 [恶搞]华为新员工转正笔试题 华为新版操作命令 Re: 有关7206路由器的问题 |